Mobile
Log In Sign Up
Home > chinese-english > "弯曲模量" in English

English translation for "弯曲模量"

bending modulus
flexural modulus


Related Translations:
弯曲毛细管:  tortuous capillary
两端弯曲:  be bends both end
弯曲河道:  meandering river channeltortuous channel
导向弯曲:  guided bend
局部弯曲:  local bendinglocal bucking
晶格弯曲:  lattice bending
快速弯曲:  quick warp
象弯曲:  image curvature
弯曲轴心:  flexural centre
强迫弯曲:  forced bending
Example Sentences:
1.Flexural modulus gpa
弯曲模量gpa
2.Paper and board - testing of cores - determination of flexural modulus by the three - point method
纸和纸板.芯层试验.采用三点法对弯曲模量的测定
3.Paper and board - testing of cores - determination of natural frequency and flexural modulus by experimental modal analysis
纸和纸板.芯层试验.通过试验模型分析法对自然频率和弯曲模量的测定
4.Prediction values of two braided composites agree well with their experimental values . influence of fiber volume content and braiding angle on specimens " strength was analyzed
从而论证了对于三维编织复合材料,测试弯曲模量和强度使用四点弯曲试验更合适。
5.The problem that ommt resulted in pvc degraded was settled . but na - mmt in pvc / na - mmt composite was simply common filler , the space of the layers was 1 . 29nm
通过力学性能测试发现,在蒙脱土含量为7phr时,硬质pvc的缺口冲击强度最大提高了108 % ,弯曲模量也有所提高。
6.Gloss . color . tensile strength . yield tensile strength flexural rigidity . flexural . elasticity . lmpact resistance . coating thichness . coating hardness . adhesion lmpact . abrasion . chemical resistance . cosfficicent of linear . thermal expan - sion thermal transmission properties . hdt
光泽.颜色.拉伸强度.屈服抗拉强度.弯曲强度.弯曲模量.抗冲击性.涂膜厚度.硬度.附着力.耐冲击.耐磨耗性.耐化学性.热膨胀系数.热传导系数.热变形温度
7.The result showed when common montmorillonite , in which the mass fraction of montmorillonite was 75 % , was used as modifier , the bending modulus of the compound increased by more than 60 % , impact strength increased by a factor of 2 , recovery ratio reduced 35 % , and the compound had good processability
结果表明,在采用蒙脱石质量分数为75 %的普通蒙脱土时,专用料弯曲模量提高60 %以上,冲击强度提高一倍,回缩率降低35 % ,并且加工性能良好。
8.The results show that fsmf can improve the bend modulus of the resin cast clearly , but reduce the tensile strength . in the suitable content of filler ( not more than 30 % in this experiment ) , fsmf can improve the tensile modulus and bend strength . in the suitable content of filler ( 20 % ~ 30 % in this experiment ) , fsmf can improve the toughness of the resin cast
结果表明: fsmf显著提高树脂浇铸体的弯曲模量,但降低拉伸强度;在合适的填料含量(本实验中为30 )下, fsmf可提高树脂浇铸体的拉抻模量和弯曲强度;在合适的填料含量(本实验中为20 30 )下, fsmf可起到增韧效果,改善树脂浇铸体的断裂韧性。
9.The intercalation mechanism of insitu emulsion polymerization has been proposed for the first time . then acr / montmorillonite nanocomposites blended with pvc , the tem and xrd indicated that the montmorillonite were dispersed with nanometer in pvc matrix . the flexural strength and flexure modulus of composites increased with the montmorillonite content , and the impact strength of composites a little increased
且随着acr蒙脱土纳米复合材料中蒙脱土用量的增加,虽然pvc acr蒙脱土纳米复合材料的拉伸性能变化不大,但抗弯强度和弯曲模量明显增大,而且其缺口冲击强度也有一定幅度的增大,具有工业实用价值。
10.Experimental and finite element analysis of three point bending ( tpb ) test were conducted . it is found material ' s anisotropy of anisotropic materials and poission ' s ratio of isotropic materials all had influence on contact deformation between specimen and fixture . so it is wise to get flexural properties using four point bending test
4 .通过试验和有限元分析发现,造成对三点弯曲试验测得的三维编织复合材料的弯曲模量远低于四点弯曲试验结果的原因:材料的各向异性和泊松比对于三点弯曲试验的压头和支座处的局部接触变形影响很大
Similar Words:
"弯曲面" English translation, "弯曲明显" English translation, "弯曲模" English translation, "弯曲模板" English translation, "弯曲模具" English translation, "弯曲模数" English translation, "弯曲模膛" English translation, "弯曲模型" English translation, "弯曲膜瞠" English translation, "弯曲幕" English translation