English translation for "弯曲模型"
|
- bending die
Related Translations:
纯弯曲: direct flexurepure bendingpure flexuresimple bending 平直弯曲: flat bendflat wise bendflatwise bend
- Example Sentences:
| 1. | Deducing the new formaulas of two isotropic materials composite yong ' s modulus from bending model
用弯曲模型推导二组元复合材料杨氏模量新公式 | | 2. | It is clearly that only two geometrical parameters i . e . maximal misalignment angle ( ) and distortion width ( s ) need to be determined experimentally
纤维弯曲模型（ fdm ）只有两个几何参数（最大纤维偏转角和变形区宽度）需要由实验确定。 | | 3. | The paper argues that there is an imperfection in the fundamental a ssumption o f g bt with regard to the traverse bending model of the plates , which consists of the thin - walled beam , and presents a new model to amend it
在广义梁理论中，有关板件横向弯曲模型的假定存在缺陷。本文就单一畸变模式新的模型对这一缺陷进行了修正。 | | 4. | The engineering constants around the stitch hole in the composite laminate are analyzed using the fdm . it is found that the elastic constants have distinct region character and the traces of the resin - rich pocket in different lamina are clear
采用纤维弯曲模型分析了缝纫复合材料单层在缝纫孔附近的最大纤维偏转角、缝纫影响区以及缝纫复合材料单层及层合板工程常数的变化，发现工程常数具有很明显的区域性，能够看出各层中树脂富集区的痕迹。 | | 5. | In this thesis the fiber distortion model ( fdm ) is presented to analyze the effect of stitching and geometry parameters on the equivalent modulus and tensile strength of the stitched composite laminates . the fiber distortion model is set up based on the microstructure of fibers near the stitch holes
为了从理论上研究缝纫对复合材料层合板面内力学性能的影响，建立了纤维弯曲模型（ fdm ） ，并且分析了缝纫参数和几何参数对层合板等效模量和拉伸强度的影响。 | | 6. | Moreover the findings also indicatedthe interface temperature stress and the basis concrete rigidity relations is not big . then , the stress distributing under load is studied , passing the four - pointbending model to analyse the interface stress under load , and giving the limitload expression of rupture destroying . analysis the interface stress under the thetemperature and stress action
其次,研究了在载荷作用下界面应力分布,通过经典的4点弯曲模型对在载荷作用下的界面应力进行了分析,给出了frp片材发生断裂破坏时的极限承载力表达式,并综合考虑了温度和载荷共同作用下界面应力分布问题。 | | 7. | The distortion of in - plane fibers is considered to be the main reason for the effect of stitching on the in - plane mechanical properties , and the fiber distortion region , the resin - rich pocket and the through - thickness reinforcement section are taken into account . the fiber misalignment angle and the inhomogeneous fiber volume fraction caused by stitching have been determined within the lamina . the elastic constants of a lamina are calculated using a micromechanical model , then the constitutive equations of the stitched composite laminates can be composed
从缝纫孔附近纤维变形的细观结构出发，建立的纤维弯曲模型，以面内纤维的弯曲变形作为缝纫影响层合板面内力学性能的主要原因，同时考虑了纤维变形区、厚度增强区以及树脂富集区的影响，得到单向板内任意一点处的纤维偏转角和纤维体积百分含量。 |
- Similar Words：
- "弯曲模板" English translation, "弯曲模具" English translation, "弯曲模量" English translation, "弯曲模数" English translation, "弯曲模膛" English translation, "弯曲膜瞠" English translation, "弯曲幕" English translation, "弯曲木" English translation, "弯曲木柄伞" English translation, "弯曲木材" English translation
|
|
|
