Chinese translation for "材料去除率"

material removing rate

Related Translations:

去除:  dislodge 短语和例子也许不用动手术就能去除他喉咙卡着的那块骨刺。 the thorn of bone may dislodge from his throat without surgery

去除瑕疵:  descabing

电解去除:  electrolyte degreasing

去除泡沫:  defoam

去除角质层:  striping of stratum corneum

去除颗粒:  t_degrain

养分去除:  nutrient removal

去除关节:  remove joint

去除幻觉:  remove illusions

污染去除:  decontaination

Example Sentences:

	1.	Material removal rate study of wire electrical discharge machining pocketing 线电极放电铣削凹坑的材料去除率规律研究
	2.	Material removing rate 材料去除率
	3.	The results show that , when increasing the feed rate of the grinding wheel , decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel , the material removal rate in the wafer rotating grinding increase , the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel , decreasing the feed rate of the grinding wheel and using finer grit grinding wheel , the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ) , beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000 , the material removal rate decreases and the wafer surface roughness has no obvious improvement 研究结果表明，增大砂轮轴向进给速度和减小工件转速，采用粗粒度砂轮有利于提高磨削矽片的材料去除率，砂轮轴向进给速度对材料去除率的影响最为显著；适当增大砂轮转速，减小砂轮轴向进给速度，采用细粒度砂轮可以减小磨削表面粗糙度；在其它条件一定的情况下，砂轮速度超过一定值会导致材料去除率减小，主轴电机电流急剧增大，表面粗糙度变差；采用比# 2000粒度更细的砂轮磨削时，材料去除率减小，矽片表面粗糙度没有明显改善。
	4.	By using a wafer - rotating grinding machine , the influence of the main process factors including grit size of diamond grinding wheel , rotating speed of the wafer chuck table , rotating speed and the down feed rate of the cup grinding wheel on the material removal rate , spindle motor current and wafer surface roughness in grinding large size wafer are experimentally investigated 摘要利用基于自旋转磨削原理的矽片超精密磨床，通过试验研究了砂轮粒度、砂轮转速、工件转速及砂轮进给速度等主要因素对材料去除率、砂轮主轴电机电流以及磨削后矽片表面粗糙度的影响关系。
	5.	The stability , rheology , chain structure and consecutive medium model in magnetorheological fluids are analyzed . according to the contribution of shear stress and normal pressure in polishing zone , the quantificational machining model of mrp is presented . as an example of plane workpiece , the influences of machining parameters on removal rate and surface roughness in mrp are studied 5 、磁流变抛光( mrf )是超光滑光学表面的一种新型加工技术，本文从mrf的磁、力学性质出发，研究了磁流液的稳定性、流变效应、链化结构和连续介质模型；根据抛光区内剪应力、正压力的分布特征，提出了mrf的定量加工模型；然后以平面工件的磁流变抛光为例，揭示了工艺参数对材料去除率和表面粗糙度的影响规律。
	6.	The cmp experiment was carried out systematically on litao3 wafer . the polished surface foughness and material removal rate in different polishing conditions were measured and the effects of polishing pad material and its condition , pressure , rotating speed of the polishing plate , the type and size of abrasive , and the properties of the polishing slurry on the surface routhness and material removal rate were analysed in details 通过对钽酸锂晶片的化学机械抛光过程的实验研究，通过测量钽酸锂晶片在不同抛光条件下的表面粗糙度和材料去除率，详细分析了抛光垫材料和状态、抛光压力、抛光盘转速、磨料种类及粒度、抛光液组成等几个因素对抛光表面质量和材料去除率的影响规律。
	7.	The solution formula of dwell time is deduced by using the pulse iteration method and the smoothing fourier transition method , and the formula can be simplified referring to workpiece shape . according to the anastomotic status of the tool and workpiece surface , we present the new model of the inherent relation among local pressure density , removal rate , convergence ratio and residual errors , and the corresponding formulas are given . the forming cause of the edge effect in the polishing process is analyzed , and the means which reduces the edge effect is put forward 2 、针对计算机控制光学表面成形( ccos )的加工方式、误差收敛特点，研制了去除函数呈高斯分布的双转子结构研抛模；采用脉冲迭代法、平滑因子傅立叶变换法推导出驻留时间的算法，求解过程中根据工件面形的特点作了各种形式的简化；提出了工件表面和研抛模的吻合误差与局部压强、材料去除率、收敛比之间内在关系的数学模型，并推导出相应的计算公式；分析了边缘效应产生的原因，在加工过程中采用相对压力因子对去除函数进行修正，可以消除边缘效应的影响。

Similar Words：

"材料清册" Chinese translation, "材料清单" Chinese translation, "材料清购单" Chinese translation, "材料情况报告" Chinese translation, "材料曲率" Chinese translation, "材料去除率超过400" Chinese translation, "材料缺乏" Chinese translation, "材料缺陷" Chinese translation, "材料燃烧性能分级方法" Chinese translation, "材料热处理学报" Chinese translation