Chinese translation for "带隙基准"

band-gap reference

Related Translations:

基准位置:  reference position

通风隙:  air course

活塞环隙:  piston ring gap

加速隙:  acceleration gap

棒隙:  rod gap

公隙:  clearance

断隙:  fault crevice

胀隙:  clearance for expansion; clearance of expansion

光隙:  light slit

地裂隙:  earth fissure

Example Sentences:

	1.	The basis topologies for the band - gap , buried zener , and xfet references are shown in figures 1 , 2 , and 3 , respectively 关于带隙基准、掩埋齐纳二极管和xfet基准的基本拓扑如图1 、 2和3所示。
	2.	The details of those cells are described . the actual circuit of current source , switch , bias and bandgap is presented 给出了实际的电流源、开关、偏置、带隙基准等单元子电路的设计结果以及仿真结果。
	3.	The linear compensation bandgap reference adopted in this thesis has limited temperature stability for ignoring the influence of vbe high order items 仿真结果表明采用高阶补偿后,带隙基准源的温度系数由22 . 8ppm /减小为7 . 8ppm / 。
	4.	According to the theory of the bandgap reference , a ptat current generator was designed , then the proportional voltage value to temperature could be achieved 利用带隙基准原理设计获得与绝对温度成正比( ptat )电流,进而获得与温度成正比的电压值。
	5.	The article analyzed and compared the type , the merits and demerits of voltage reference , pointed out the advantages of bandgap reference ( bgr ) , and the improved configuration of bgr was chosen 对基准源的类型和优缺点进行了分析和比较,指出带隙基准源的优点,选取了改进型带隙基准源的结构。
	6.	Based on the whole chip function requirements , sub - block design and simulation were completed , including bandgap voltage reference , oscillator , slope compensation , current sensing , control and drive logic 在子电路的设计上,作者主要介绍了带隙基准电压源、振荡器、斜坡补偿、电流感应、控制和驱动逻辑。
	7.	The circuit design of bandgap voltage reference is completed , considering the high order temperature compensation with real resistors . the circuits designed have been simulated , using csmc 0 . 6um cmos parameter files 在考虑利用实际电阻的温度系数来进行带隙基准高阶温度补偿的基础上,实现了带隙电压基准源的电路设计。
	8.	To cancel the offset - voltage of the comparator , a switch capacitance circuit is used between the three pre - amplifier stages . the charge pump circuit is used to boost the clock voltage of the switch transistor 采用电荷泵电路提供开关管栅过驱动电压，带隙基准电路作为电荷泵稳定电压的输入，有利于改善开关电路的性能。
	9.	So far , the bandgap reference is the most popular circuit , which successfully achieves the requirements mentioned above . it exhibits both high stability and low temperature coefficient , also has low noise and simple topology 其中，带隙基准电压源因其高稳定度、低温漂、低噪声且构成简单等优点而得到普遍重视，亦为本文所采用。
	10.	The dac consists of analog circuit blocks and digital circuit blocks , so it is a mixed signal circuit . because the digital part is simple comparatively , we use the same method as analog part to design it 采用模块化的设计方式实现数据快速转换,主要包括电流源矩阵模块、锁存模块、译码模块、带隙基准电压源模块及电流开关网络等电路模块。

Similar Words：

"带系" Chinese translation, "带系列" Chinese translation, "带隙" Chinese translation, "带隙电压参考" Chinese translation, "带隙构造" Chinese translation, "带隙晶体" Chinese translation, "带隙能" Chinese translation, "带隙跃迁" Chinese translation, "带细孔" Chinese translation, "带细孔的" Chinese translation