English translation for "最大拉应力"

maximum tension stress

Example Sentences:

	1.	The maximal tension stresses in surface and base between induced crack have been obtained by parametric analysis 通过结构参数分析掌握了预切缝间面层、基层中最大拉应力的分布规律。
	2.	The maximum draw stress located on the lingual apex , while the maximum compressive stress located on the lingual crest of the ridge 最大拉应力位于舌侧根尖部，最大压应力位于舌侧牙槽嵴顶。
	3.	Then , taking the maximal tension stress in surface and base and the stress intensity factor at the top of the induced crack as restraining indexes , method to determine the reasonable induced spacing has been determined 然后以预切缝上端应力强度因子、面层与基层内的最大拉应力为约束指标建立了合理预切缝间距的确定方法。
	4.	The models of analyzing temperature and structure are established . temperature increment and deformation are discussed with finite element method and ordered coupling method . maximum tensile stress criterion is chosen as the destroying criterion of components 首先建立了光学元件温升和结构分析模型，用有限元法和序贯耦合法计算材料的温升和变形，同时选取最大拉应力准则作为材料的破坏准则。
	5.	When the fill factor is less than 1 , the concentrated tensile stress appeares near edge of disk surface , while the fill factor reaches up to 1 , the surface exhibites compressive stress , and the center is less tensile stress 当抽运光斑未充满激光介质时，介质的表面靠近边缘处会出现大的拉应力集中，并且介质表面的最大轴向位移和最大拉应力随光斑填充因子增大而增大；而当抽运光充满介质时，表面是压应力，较小的拉应力存在于介质内部。
	6.	According to differences of construction process , boundary condition , temperature and stress of two schemes extending 3m deep short seam on upstream face in the middle of rcc overflow section and no short seam are calculated , what " s more , in this paper the equivalent line drawing of stable temperature field and unstable temperature field during construction and operation period and the duration curve drawing of typical points " s temperature and stress are plotted , and the results of peak and minimum on temperature in every month and maximum on tensile stress are attained 根据施工过程和边界条件，对溢流坝段中间上游面增设3m深短缝和不设短缝两个方案进行了温度和应力计算，并绘制出稳定温度场等值线图及施工期、运行期非稳定温度场等值线图，典型点温度和应力历时曲线图，逐月最高、最低温度和最大拉应力及相应位置等成果。
	7.	When the pumping area cannot approach the disk had aperture , the concentrated tensile stress appears near the edge of disk hard aperture , while the disk is pumped full aperture the surface exhibits compressive stress , and center is tensile stress which is lesser 当抽运光斑未充满激光介质时，介质的表面靠近边缘处会出现大的拉应力集中，并且介质中最大拉应力和表面的最大轴向位移随抽运光斑尺寸缩小面增大；而当抽运光充满介质时，表面是压应力，较小的拉应力存在于介质内部。
	8.	3 . base on the numeric method of finite element , the influence of interrelated shift coefficient and tooth number z to bend intensity of gear is studied . with the increase of the tooth number , tooth root maximum pull stress decrease ; with the increase of the interrelated shift coefficient , tooth root maximum pull stress increase 3 、基于有限元数值计算方法，分析了不同关联变位系数和齿数z对齿轮弯曲强度的影响：随着齿数的增大，齿轮最大拉应力减小；关联变位系数越大，齿轮最大拉应力越大。
	9.	Because of the complexity of calculation result data , and in order to simplify the analysis of results , this paper only provides annual temperature isoline map of february , may , august and november during construction , temperature isoline map of the first , fifth , tenth , twentieth and thirtieth year during operation , duration curve of temperature and stress of typical point at different elevation , the maximal stress distribution along dam height , point at different elevation , the maximal stress distribution along dam height , and the maximal and minimal temperature and the maximal tensive stress and its position of every month 因计算结果数据量非常大，为便于成果分析，本文仅给出施工期每年2 、 5 、 8 、 11月份和运行期第1 、 5 、 10 、 20 、 30年的温度等值线图，坝体不同高程典型点温度和应力历时曲线图，最大应力沿坝高分布图，逐月最高、最低温度和最大拉应力值及相应的位置等。

Similar Words：

"最大拉伸比" English translation, "最大拉伸强力" English translation, "最大拉伸应力" English translation, "最大拉条距离" English translation, "最大拉细比率" English translation, "最大来源" English translation, "最大浪速线" English translation, "最大浪涌电流" English translation, "最大劳动负荷量" English translation, "最大劳动量法则。" English translation