| 1. | The theoretical curves are reversed respectively
分别对理论曲线进行了反演。 |
| 2. | Compare the theory curve with the experimental curve , analyse the difference between the two curve
比较分析了实验曲线与理论曲线的不同，并就引起这些不同的原因进行了分析讨论。 |
| 3. | Evaluating factor : this is a figure indicating the match condition between the calculated and real time measured spectral
评价函数：是评价实际镀制中光谱曲线与理论曲线吻合程度的数值。 |
| 4. | The energy transmission along the axes is accord with the academic calculation . under simultaneity driven , the energy radiated by point source array increasing according to cell number is proved by experiment
超短脉冲单辐射器轴线上能量传播的实验与理论曲线几乎一致，同步激励时点源阵辐射的能量按单元数平方律增加得到了较好的实验验证。 |
| 5. | Finally , comparing the deforming and reversing of the metal diaphragm and the result of simulation with the theory curves and experiment result , we got the correct conclusion . it also supplied an evidence for diaphragm changing
最后,将膜片的翻转变形过程模拟曲线、模拟结果分别与理论曲线、实验结果进行了比较,验证了本文正确性,计算结果可以为膜片的设计提供参考。 |
| 6. | The comprehensive research of typical wells in water - yield pattern shows that the theoretical curves are accordant with actual situation , indicating this method is applicable to analysis and prediction of water - yielding pattern in such a reservoir
对典型井的产水规律综合研究表明，理论曲线与油藏实际产水情况比较吻合，说明该方法对薄层底水油藏产水规律分析预测具有较好的适用性。 |
| 7. | The inversion results of synthetic magnetotelluric sounding data are ideal , which indicates that the algorithm possesses advantages of expediting convergence , avoiding earliness and improving precision , and can be used in mt data analysis
对各种类型的大地电磁测深理论曲线进行计算，结果表明：采用实数编码混合遗传算法进行反演具有收敛速度快、解的精度高和避免出现早熟等优点，可用于大地电磁资料解释。 |
| 8. | This paper analyses emphatically the position error and manufacture error of critical - angle prism the position error and aberration of object lens the position error and manufacture error of the polarization beam splitter the position error of the detector , and come out their relations
着重分析了临界角棱镜位置误差与制造误差；物镜的位置误差与像差；偏振分束棱镜的位置误差与制造误差；探测器的位置误差等对离焦误差信号的影响，并给出了理论曲线。 |
| 9. | In this paper , on basis of the current machining state , a testing principle on aspheric surface is put forward to , the principle is a kind of touching method by testing the meridian of aspheric surface and comparing it with the theoretical curve , so surface figure error is got . according to this principle , mechanical structure is designed and electric - control system is researched
本文首先基于现阶段非球面的加工状况，提出了用接触式检测非球面的子午面面形曲线并与理论曲线相比较，从而得到非球面面形误差的检测原理，并根据该原理进行了机械结构的总体设计和电控系统的研究。 |
| 10. | 4 . based on the theory - character parameter , this paper presents the theory equation for stress - stain complete curves of the rpc filled steel tube , it is founded that computed curves are in good agreement with the tested one , and it can be applied for the all course analysis of the rpc filled steel tube
4 、基于上述圆钢管rpc轴压柱的理论特征参数，推导建立了圆钢管rpc轴压柱应力应变全曲线理论方程，该方程理论曲线与试验曲线相当吻合，可用于圆钢管rpc构件的全过程分析。 |
