Chinese translation for "焊接顺序"

sequence of welding
welding sequence
weldingsequence

Related Translations:

焊接:  weld; welding; soldering; seal; sealing; sealing-in; shutting together 短语和例子电弧焊接 (electric) arc welding; 焊接材料 welding material; 焊接操作 welding operation; 焊接车间 welding shop; 焊接点 point of weld

纵向焊接顺序:  longitudinal welding sequence

构件焊接顺序:  block welding sequence

钻孔顺序:  drilling sequence

顺序解释:  sequential interpretation

顺序属性:  sequential attribute

顺序编排:  sequential organization

含水层顺序:  aquifer sequence

改变顺序:  change in sequencepermute

顺序测量:  proceeding measurement

Example Sentences:

	1.	Assembly ? welding sequence : the configuration which had been whole assembled can decrease welding deformation for configuration rigidity had been added 装配?焊接顺序：将结构总装后进行焊接，由于结构刚性增加，可以减少焊后变形。
	2.	Different assembly ? welding sequence may result different risidual deformation , we usually take fixup by spot welding first , then take welding symmetrically 不同的装配?焊接顺序，焊后产生不同的残余变形，一般是先点固，再进行对称焊接。
	3.	A design approach to the 3d cad of welded machine is presented in this thesis , in which the rules of bar orientation , joint processing and welding sequence are stressed 本文提出了一个面向焊接机架的三维cad方法，着重研究混合型钢结构的杆件布置、节点处理和焊接顺序自动生成方法。
	4.	The minimal deformation of the structure is obtained using the method presented as follows : four web plates are first tack welded on both ends , and then the web plates are 采用设计的焊接顺序在导弹油箱壁板实际结构上进行焊接并对焊后壁板变形进行了测量,测量所得的壁板变形规律与模拟计算结果吻合良好。
	5.	Factors including welding sequence being input of the network , and welding distortions being output can make the resulting network which is used for the model of welding distortion and its fast forecasting 以焊接顺序等因素作为网络输入，以钢结构板材凹凸变形为输出，训练生成网络焊接变形模型，可用于预测船舶钢结构焊接变形量的快速预测。
	6.	Welding position : if the configuration collocation of weld is symmetry and the welding sequence is reasonable , the longitudinal contraction and transverse lateral contraction deformation are usually produced , incontrast , the bending deformation is usually produced 焊接位置：如果焊缝在结构布置对称，焊接顺序合理时，则主要产生纵向收缩和横向收缩变形，反之，则要发生弯曲变形。
	7.	3 according to analysis on the reason for failure of joints , improved measures for new joints are presented , the following phases are included , improved butt welding design , improved technology and welding sequence for butt welding seam , intensive strength checking for butt welding seam , intensive quality inspection for butt welding seam (三)通过对节点破坏成因的分析，提出了新型节点的改进措施，包括四个方面：改进对接焊缝的设计、改进对接焊缝的焊接工艺和焊接顺序、加强对接焊缝的强度校核、加强对接焊缝的质量检测。
	8.	As an application of this fem preprocessing system , the simulation on the welding process of missile ’ s oil box was performed , in which the effects of the welding sequences of four web plates and welds on each web plate are primarily analyzed . the simulation results show that the deformations under varied welding sequences are almost the same . downward deflection deformation is obtained along the weld longitudinal direction in the structure as well as upward deflection deformation along the weld traverse direction 对于某型号导弹油箱结构焊接过程的数值模拟计算,主要考察了每块立板上各段焊缝焊接顺序的调整、四块立板之间不同的焊接顺序以及焊接起始端的选择对结构焊后变形的影响规律,模拟结果表明:壁板在各种焊接顺序下的整体变形规律基本相似,即焊后壁板沿焊缝纵向发生了向下的挠曲变形,中部向下变形量最大;沿焊缝横向发生了向上的挠曲变形,壁板两端部变形量较大,且壁板前端变形大于壁板后端。
	9.	The design process of the proposed method is described as follows : the user inputs the 3d sketch of a welded machine , and the geometry and topology information of the members in the welded machine are established automatically . the design information is acquired by the means of man - computer interaction . according to the knowledge of design and welding , the rules of bar orientation , joint processing and welding sequence are established 用户在autocad中输入焊接机架的线框简图，提取出机架结构的几何和拓扑信息，然后通过人机交互输入设计信息，并根据机架的设计知识与焊接知识，建立机架的杆件方位布置规则、节点处理规则与焊接顺序自动确定规则，最后在autocad中生成经过节点处理的机架三维实体，并提供一套合理的焊接顺序。

Similar Words：

"焊接手套" Chinese translation, "焊接首柱" Chinese translation, "焊接输入热量" Chinese translation, "焊接术语" Chinese translation, "焊接瞬时应力" Chinese translation, "焊接速度" Chinese translation, "焊接速度，接合速度" Chinese translation, "焊接速率" Chinese translation, "焊接胎架" Chinese translation, "焊接胎架，可动焊接工作台" Chinese translation