Chinese translation for "比压"

beta ratio
ecific pre ure
specific pressure
unit pressure

Example Sentences:

	1.	Broad - based projects use off - road tires , adhesion , grounding than the small , and their climbing ability 采用宽基工程越野轮胎，附着力大，接地比压小，爬坡能力强。
	2.	The basic structure and the seal principles of the hard packing were presented , and the formula of specific pressure was given 介绍了硬填料密封的基本结构及密封原理，给出了比压计算式。
	3.	The cross - section area of the internal sprue , the fill speed , the fill time and injection pressure are important die casting technology parameters 摘要内浇道截面积、充填速度、充填时间和压射比压都是重要的压铸工艺参数。
	4.	Tys120llgp bulldozer is rigid suspended , power shift , hydraulically controlled and track - type . it is applicable for the extra requirement of the ground pressure Tys120超湿地推土机系刚性悬挂、机械和动力换档变速传动、液压操纵的结构型式，是一种能满足使用工况对接地比压有特殊要求的湿地型履带推土机。 。
	5.	The chemical reaction control of cuo - al system has been studied . the results show that the chemical reaction is more stable when cupric oxide and aluminium is put respectively into molten copper 在此基础上，实验研究了cuo ? al体系的化学反应控制，得出了采用cuo和al分别加入法比压块加入法会使反应进行的更加平稳。
	6.	Tys165 bulldozer is of power shift , hydraulically controlled and track - type . it features good performance , flexible operation , good quality , high efficiency , especially used in waterlogged area Tys165推土机系液力机械传动、液压操纵、低比压履带推土机。该机性能优良，操作灵活方便，质量可靠，工作效率高，特别适合沼泽地和含水量比较高的松软地带使用。
	7.	The cross section area of the internal sprue of the die casting dies designed should be of proper value , and matches perfectly the fill speed , the fill time and injection pressure in case that the die casting dies fail in the design 设计压铸模时应当确定恰当的内浇道截面积，并使之与充填速度、充填时间和压射比压保持较好的匹配，以防止压铸模设计的失败。
	8.	According to simulation results we decide the location of parting face and cooling system 、 the shape and location of runner and gating system etc . after that we take the az91d magnesium alloy shell of motorcycle engine as an example to proceed fine factors ( plunger injection speed 、 pouring 然后以az91d镁合金摩托车发动机外壳为例,进行五因素(压射速度、浇注温度、锻造时间、压射比压、锻造压力)四水平l16 ( 45 )正交实验,在普通压铸过程中关闭锻造功能。
	9.	Touch on developing large - flow and high - pressure ratio impressor and large - enthalpy drop turbine , reducing harmful emission , solving the major problems of high - temperature blade material , cooling , protective coating and single - grain blade casting , and comfirm some important manufacturing techniques 涉及了开发大流量高压比压气机、大焓降涡轮，降低有害排放量，解决高温叶片的材料、冷却、保护涂层及单晶叶片铸造等主要问题，并确认了一些关键的制造技术。
	10.	According to the moving characteristics of tracklayer , when the vehicle is on ramp and the ground ' s vertical pressure is linear , the calculating formulas of relationship between the deviation of the instantaneous steering center , the position of vehicle ' s gravity , steering radius , moving velocity , moving acceleration , and vehicle ' s orientation , were obtained by the theory and method of vector analysis in mathematics and mechanics 摘要根据履带式车辆的运动特点，运用数力学中矢量分析理论和方法，推导了接地比压为线性分布时履带式车辆在斜坡上转向时，瞬时转向中心偏移量与车辆重心位置、转向半径、行进速度、加速度、车辆方位相互关系的计算公式。

Similar Words：

"比学赶帮超" Chinese translation, "比学说" Chinese translation, "比雪夫" Chinese translation, "比雪夫型" Chinese translation, "比逊河" Chinese translation, "比压规范" Chinese translation, "比压器" Chinese translation, "比压器,计器用变压器" Chinese translation, "比压头" Chinese translation, "比压应力" Chinese translation