| 1. | Quantitative control of peer review subprocess in implementing cmm cmmi
中同行评审子过程的定量控制 |
| 2. | The assessment of system reliability is the necessary means to fix quantify of system reliability
系统的可靠性评估是对系统的可靠性进行定量控制的必要手段。 |
| 3. | Controls cost by minimizing spoilage , maintaining adequate inventory of food , utilizing food surpluses and portion control
通过减少食物浪费，维持适当合理的食物贮存量和充分利用多余食物和进行定量控制，以降低成本。 |
| 4. | And the effect of the dynamic characteristics of the electromagnetic switch on the quantitative controlled material flow was analyzed theoretically
从理论上分析了填料装置中电磁开关的动态响应特性对物料定量控制精度的影响。 |
| 5. | The result indicated that the system had good step response and tracking performance and met the requirement of quantitative control of cycling power
结果表明所设计控制系统阶跃响应性能良好,并有较好的跟踪性能,能够满足训练者运动定量控制的要求。 |
| 6. | Under special working conditions , a meshed board at the entrance of the feeder was designed and set to quantitatively control the flow of a superfine material with special properties
摘要根据某种微细物料的物理特性和添料工况要求，采用在料斗口安装网孔板的方法实现对物料流量的定量控制。 |
| 7. | The control precision of perfusion measure affects directly encapsulation quality , so the paper analyzes factors , which affect precision of perfusion measure , and also design a control scheme
灌注量的控制精度直接影响了太阳能电池板的灌封质量，故本文分析了影响灌注精度的多种因素，并设计一种定量控制方案。 |
| 8. | The results of the system test and prototype application showed that the grease quantity and lubricating timing for vehicles could be achieved , the lubricating operation was stable and credible , and the control methods were reasonable and intelligent
系统性能检测和样机应用试验表明，该系统能实现底盘油脂润滑的定时定量控制，工作稳定可靠，控制方法合理可行，智能化程度高。 |
| 9. | On the purpose of catching up with the advanced level of the world , and developing microinjection devices of ourselves to promote the chinese gene engineering , this paper is dedicated to the design and fabrication of the microinjection volume controller and the research on the detection of microinjection volume by micro - vision , based on looking into the advanced products mentioned above and researches on the dynamical characteristics of the dna micro - fluid from both theoretical and experimental aspects
为了追赶世界先进水平，同时也为了开发具有中国特色的显微注射设备，以推动我国基因工程的发展，本论文在深入调查了解国外先进产品，以及从理论及实验方面对dna微流体的动力学特性进行研究的基础上，致力于微注射量控制器的设计与研制，以及显微视觉检测技术的研究，以便对其进行更有效、更精确的定量控制。 |
| 10. | This article introduces a method of dynamic weighing and predetermined controlling . and in order to minish error in dynamic weighing , this article has adopted multilevel controlling with a suit of controlling arithmetic , and it has adopted a dynamic weighing method , so the speed and precision of weighing have improved , and to some extent it has offset the deficiency just in unilateral dynamic weighing or unilateral predetermined controlling
本论文中概述了动态称量技术国内外研究现状和发展，说明了研究动态称器的必要性和迫切性，本文是把动态称量和定量控制相结合，使控制算法来实现多级控制，从而提高了称量的精度和速度，弥补了单独提高动态称量精度或单方面优化定量控制策略的不足。 |
