Mobile
Log In Sign Up
Home > chinese-english > "铸膜" in English

English translation for "铸膜"

casting film

Related Translations:
铸谷:  itani
电铸:  (利用电解作用获得金属复制品的一种方法)1.[冶金学] (电冶; 电解成型) electroforming; electroform2.[印刷] electrotyping; galvanoplasty; galvanoplastics (制版法)◇电铸成型 electrotyping forming; 电铸制版法 galvanography
连铸:  cc dr processcontinuous casting direct rolling processo continuous casting
铸坑:  [工业] foundry pit; casting pit
铸压:  coining
铸塑:  cast
铸废品:  off castoffcast
整体铸:  integral casting
干铸:  dry casting
铸漏:  bleedbreak outrun-out
Example Sentences:
1.Specification for tfe - fluorocarbon resin cast film
Tfe碳氟树脂铸膜规范
2.Effect of polyethlene glycol on membrane forming systems and polyethersulfone with cardo performance and structure
聚乙二醇对聚芳醚砜铸膜液体系及膜性能与结构的影响
3.The effect of nonsolvent additives on poly phthalazinone ether sulfone membrane - forming systems and membrane properties and structure
非溶剂添加剂对共聚砜铸膜液体系及膜性能与结构的影响
4.2 . the effects of pre - evaporation time on the structure and properties of pes membranes by two - step formation
东华大学硕士论文2 .研究了铸膜液的预蒸发时间对二次成形聚醚矾膜结构与性能的影响。
5.The effects of pes concentration and temperature in casting solution on the structure and properties on pes ultrafiltration membranes are studied
研究了铸膜液中聚醚砜的质量分数和温度对膜结构与性能的影响。
6.The studies on stability of pu - sio2 , pes - sio2 suspensions and influence coagulant bath temperature on flat membrane were carried out
研究了无机粒子填充聚合物悬浮铸膜液的稳定性及凝固浴温度对平板膜成形的影响。
7.Based on former studies , the effect of low licl concentration in casting solution ( w ( licl ) ) on membrane structure and performance was studied
在前人研究的基础上,着重研究了铸膜液中无机添加剂licl的浓度( w ( licl ) )较低时对pvdf膜性能和结构的影响。
8.Research of composite pvdf membrane properties composite pvdf membrane was produced via adding support in order to improve the strength of membrane
Pvdf复合膜性能的研究。在初步确定的铸膜液配方及涂膜工艺的基础之上,为提高pvdf单膜的强度,引入支撑体制得复合膜。
9.The membranes exhibit good hydrophilic performance and high water flux with highly loose and inter - connective microstructure , which is potential for the separation of protein
优化了制膜工艺条件,并对影响膜结构与性能的一些因素,如聚合物浓度、添加剂含量、铸膜液温度和凝固浴温度进行了研究。
10.As the temperature increases , the water flux first decreases evidently , then increases slightly and the clearance rates of low - molecular weight substances first increase , then decrease shaply
随着铸膜液温度的上升,水通量先是明显下降,然后略有上升。膜对低分子物质的去除率先是增加,然后急剧下降。
Similar Words:
"铸模型腔" English translation, "铸模用钩头钉" English translation, "铸模用润滑油" English translation, "铸模组合" English translation, "铸模座" English translation, "铸膜核心" English translation, "铸膜料斗" English translation, "铸膜液" English translation, "铸镍" English translation, "铸排" English translation