| 1. | Design software . maybe work on simulation games
设计软件可能设计模拟类游戏 |
| 2. | Design simulation and matching test of intake ports for four - valves diesel engine
4气门柴油机进气道的设计模拟及试验匹配研究 |
| 3. | ( 2 ) the design of the important parts is optimized with ansys software then getting the optimized design method
（ ）用ansys工程分析软件对氧传感器的重要部件进行了设计模拟，从而得出最优化的设计结果。 |
| 4. | We also design a voice transmitting software , which can simulate voip within lan environment with visual c + + so as to realize full - duplex voice communication in two computers on internet . the project includes two parts : multimedia ( includes recording and playing ) and transmission
并用visualc + +设计模拟voip的小型局域网上的语音传输软件，实现internet上两台计算机的全双工语音通信，主要包括多媒体部分(录音、放音)和传送部分。 |
| 5. | Stress concentration measure on the model of boiler drum with two nozzles was executed and the testing results were compared with the asme criterion , experiential value and the value of finite element method respectively . this measurement result provides direction for evaluation of stress amplitude
设计模拟汽包进行应力测试，并与美国asme规范和经验公式计算值、有限元计算结果进行比较，为后续的低周疲劳寿命估算时交变应力幅值的确定提供依据。 |
| 6. | The main two process of the development on system is as follows : part one : using prote199 software to design the sch chart of the analog signal input card and complete pcb charts , then have them made in factory ; to debug on the hardware ; to program assemble language control software of the analog signal input card and debug on the super ice 16 simulator ; to utilize the super ice 16 simulator to link card to debug the control programs online ; to embed the control program debugged successfully into eprom and debug the system on eprom
系统研制开发过程主要分两大部分：第一部分：应用protel99设计软件设计模拟量输入卡的硬件原理，规划设计印刷电路板图并送厂制作板卡电路板；模拟量输入卡硬件制作和调试；编写模拟量输入卡汇编语言控制程序，在superice16仿真器上编译调试；编译后的控制程序在superice16仿真器上以在线方式仿真调试；仿真调试成功的控制程序烧入eprom芯片，进行系统eprom仿真调试。 |
| 7. | The paper presents the detail design methods of supervising the remote terminal . the system could simulates field , show the data transformation dynamically , give an alarm , give data report forms and historic database . then the system transmits the data from data collected station to control center
本文对基地的机房远程监控系统提出了具体的设计方法，利用组态王设计模拟现场，动态的表示现场数据变化，实现报警、数据报表、历史数据库等功能以及将数据从各数据采集站发布到基地监控中心。 |
| 8. | The paper introduces these technologies as fellows : ( 1 ) the overview of virtual instrument ( 2 ) pci bus protocols and specifications ( 3 ) hardware section analogue signal conditioning circuit high speed a / d conversion circuit fpga circuit pci bus interfacing circuit ( 4 ) software section visual c + + programing hardware driver programing vhdl programing ( 5 ) the method and result of system test
论文从以下几个方面进行了阐述： ( 1 )虚拟仪器概述( 2 ) pci的协议规范( 3 )硬件电路设计模拟信号调理电路设计高速a d转换电路设计fpga电路设计pci接口设计( 4 )软件设计visualc + +编程设计底层驱动软件编写设计vhdl编程设计( 5 )系统调试方法和结果 |
