English translation for "离心力作用"

centrifugal action

Related Translations:

离心力:  centrifugal force; centrifugal pull◇离心力场 centrifugal force field; 离心力除尘器 centrifugal collector; 离心力干燥法 centrifugal seasoning; 离心力继电器 centrifugal relay; 离心力试验 whirling test

离心力卸货:  centrifugal discharge

离心力风扇:  centrifugal fan

离心力负载:  fliehkraftbelastung

离心力场:  centrifugal fieldcentrifugal force fieldcentrifugalforcefieldcentrifuge field

离心力试验:  whirling test

离心力除尘器:  centrifugal collector

相对离心力:  maxrcfrelative centrifugal force, rcfrelative centrifuge force

最大离心力:  g-forcemax rcf

离心力矩:  centrifugal moment

Example Sentences:

	1.	08 . 02 test method for plasticizer sorption of poly vinyl chloride resins under applied centrifugal force 离心力作用下聚氯乙烯树脂增塑剂吸附作用测试方法
	2.	Standard test method for plasticizer sorption of poly vinyl chloride resins under applied centrifugal force 在离心力作用下聚氯乙烯树脂的增塑剂吸收作用的试验方法
	3.	Material is fed into the inner cylinder of the feeding scroll through a feed pipe and into the solid - bowl after the acceleration 物料由进料管连续引入输料螺旋内筒，加速后进入转鼓，在离心力作用下，较重的固相物沉积在转鼓壁上形成沉渣层。
	4.	Pour detergent into the water inlet round hole on the cover of dehydrator , then connect the hose , turn bent faxle handle , waterrom 16 inlets spout to the cleaned part of rotating roller , so , under the function of centrifugal force , the high speed turningrotating roller can completely stir water , therefore achieve thecleanness effect ：洗涤剂从脱水器盖子上加水口圆孔加入，接入水管,摇转曲轴手柄,水就从上，而下于16个出水孔喷射向高速旋转的滚筒需清洁部位,高速旋转的滚筒在离心力作用下搅动产生水旋涡，从而达到洗涤效果。
	5.	The result of the calculation for tip clearance is reasonable when it is compared with theory . two ways are put forward for convention of dimension of the turbine components from high temperature to low one , which is related with tip clearance , a simple example is used to illuminate that the two ways are useful , using the method of design optimization , axiisk and a blade of a certain turhine is analysed , it showes that the method of design optimization is feasible to be used for convertion of dimension of the turbine components . finally , ansys software is used to analyzed the variation of tip clearance with the method of cyclic symmetry analysis when engine works under the conditions of temperature and rotational speed , am using a new method to deal with thermal contact resistance in the calculation 本文完善了计算涡轮叶尖间隙的简化算法程序，增加了程序的计算功能，并将其应用于某高压涡轮进行叶尖间隙分析，所得结果与理论结果进行了对比，得出修改后的程序用于叶尖间隙计算是合理的；同时提出了与叶尖间隙相关的涡轮典型部件的冷、热态的尺寸两种换算方法，使用优化设计的方法进行了实例分析，说明了所提出的计算方法是可行的；最后应用ansys有限元软件利用循环对称的方法分析了某型发动机高压涡轮在温度场及离心力作用下的叶尖间隙在发动机工作过程中变化情况，并分析了计算中的接触热阻的处理问题。
	6.	As the deformation caused by centrifugal force is beyond the small deformation range , the large deformation effect was also taken into account in the equation . two models are constructed , one is of shrouded blade and the other is of bladed disc . the static natural frequencies and dynamic frequencies ( under 3000rpm ) are calculated by the finite element method and cyclic symmetry technique 针对叶片的结构特点,采用适应较强的三维八节点实体单元模拟叶片,建立叶片运动微分方程;叶片?轮盘系统在高速旋转时,受到离心力作用,使叶片发生大变形,故在方程中考虑了几何大变形的问题;为研究叶根轮缘之间的接触状态,建立了考虑叶根?轮缘接触的有限元方程,利用拉格朗日增广算法来求解该方程,确定叶根轮缘之间的接触面状态。
	7.	As to the high speed of electric spindle system , the angle - contact bearings are usually applied to supporting the shafts . because the supporting stiffness of rolling bearing is non - linear , especially under the circumstances of high speed and ultrahigh speed , the internal working status is so complicated that it is not regarded as routine linear support and ordinary non - linear support . centrifugal effect of the rolling bearing increase the factors of influencing the supporting stiffness 高速电主轴系统的转速很高，通常都采用角接触球轴承作为支承，由于滚动轴承的支承刚度呈非线性形式，特别在高速和超高速情况下，滚动轴承内部的动力学状态十分复杂，由于滚动体运动所产生的离心力作用，使得影响其支承刚度的因素增多，不能作为常规的线性支承和普通的非线性支承处理。
	8.	After the machine stops , open its cover , loosen the lock blocks on lip ring , suspend the lip ring together with the filter bag containing cake to the place for discharging , then have the bottom of the filter bag splay , thus the cake being discharged automatically 在离心力作用下，液相物穿过滤布和转鼓壁滤孔排出转鼓，经排液管排出机外，固相物截留在转鼓内，停机后启开机盖，松开拦液板锁紧块，将拦液板连同装有滤渣的滤袋一并吊往卸料处，使滤袋底端落下张开，滤渣自动排出。

Similar Words：

"离心力偶" English translation, "离心力式平衡机" English translation, "离心力试验" English translation, "离心力位" English translation, "离心力卸货" English translation, "离心联轴器" English translation, "离心连铸" English translation, "离心淋洗色谱法" English translation, "离心流散效应" English translation, "离心路径" English translation