| 1. | Secondly in order to make sure the link of hardware , it is necessary to write hardware drive program
其次为实现硬件连接，还需要根据硬件电路书写硬件驱动程序。 |
| 2. | While sophisticated hardware linkages aren t exactly commonplace , they re much better understood than they were in the past , and form the basis for many commercial platforms available today
尽管复杂的硬件连接并不简单，但是人们对它的理解却达到了前所未有的深度，并构成目前使用的很多商用平台的基础。 |
| 3. | A intelligent can - pc bus card , a multi - port serial card and a 100 / 10m self - adjust network card are used to maintenance the stability and real - time capability of receiving and sending data in the communication subsystem
在硬件连接设计上采用了智能can ? pc总线适配卡、多串口卡和100 / 10自适应网卡等不同的设备，保证了数据接收、传送的实时性和稳定性。 |
| 4. | Based on low power consumption mcu msp430f , the paper introduces the method of designing the human - computer interaction interface module , and presents the hardwire circuit and the pivotal steps of using state - analysis to design human - computer interface
摘要介绍了基于超低功耗单片机msp430f的人机交互接口模块的设计方法，给出了硬件连接图及状态分析法设计人机接口的几个关键步骤。 |
| 5. | Firstly , the paper explains the specialty of pci bus and plx 9030 interface chip , then describes how to use it in this project . it includes the hardware connection and the software configuration , which is introduced especially
本文首先阐述了pci总线和plx9030接口芯片的特点，以及plx9030在课题中的使用方法，包括plx9030芯片的硬件连接和软件配置，其中着重介绍了软件配置部分。 |
| 6. | Finally it designs the method of assorting with and monitoring all kinds of hard - function modules , and discusses the problems of nc language and hard - connection between the machine and the controllers during realizing full open architecture pcnc
最后，给出pcnc中各硬件功能模块协调工作与监控的设计方法，并讨论了全开放pcnc实现中的数控加工语言和机床与控制器的硬件连接两个问题。 |
| 7. | This paper presents the characteristic and working principle of the max813l as well as its application to the anti - interference of the 51 - series microcomputer system . the paper also describes the hardware connection circuit and the corresponding programming technique of software anti - jamming
文章介绍了max813l的性能特点和工作原理，并给出了在51单片机系统抗干扰中的具体应用实例，详细介绍了硬件连接电路和相应的软件抗干扰编程技巧。 |
| 8. | The minimum control system of single - chip micro - controller has two part of binary systems serial communication . for the communication between pc and the single - chip instrument , i chose to connect a chip named max232 to proceed the level conversion in electricity , establish the correspondence agreement , drawing the hardware connection diagram , and designed the correspondence procedure process with parts of procedures code ; for the communication between the single - chip instrument and the fx489 , thesis uses 8251a to expand 89c51 for a serial port
对于pc机和单片机的通信，论文选择了接口芯片max232进行电平转换，设定了双方通信协议，画出硬件连接图，并设计了通信程序流程及部分程序代码；对于单片机和fx489之间的串行通信，论文采用了8251a扩展了89c51的一对串行口，同时也设计了这部分的通信程序流程及程序代码；另外，还对89c51扩展了一片数据存储器6264 。 |
| 9. | This paper designs the hardware circuit and completed the hardware manufacture of the slave node . the slave node combined with the 5136 - dnp - pci master board made by woodhead company make up of a typical master / slave network . an easy build and reliable hardware solution is available in this paper
本文设计了从站通讯接口的硬件连接原理图，完成了硬件电路板的制作，并与woodhead公司的5136 - dnp - pci主站卡一起组成了一个典型的主从网络，从而提供了一种易实现、高可靠的硬件解决方案。 |
| 10. | Abstract : the paper introduces the controlling system of virtual instruments for the model of cotton grabbing machine and discusses mainly the hardware connecting and software of the controlling system of virtual instruments . the result of the system indicates that more applying systems can be developed in the construction of laboratories with the help of virtual instruments
文摘:介绍了抓棉机模型虚拟仪器的控制系统，着重讨论了虚拟仪器硬件连接和软件程序；该套系统的成功运行结果显示，在实验室建设中运用虚拟仪器还可开发出更多的应用系统。 |
