English translation for "球直径"
|
- ball diameter
spherical diameter
Related Translations:
投影直径: diameter projectedprojected diameter 喷嘴直径: jet diameterorifice size 钻孔直径: borehole diameterdiameter of borediameterofboredrilled diameterhole sizeholesizewell diameterwelldiameter 内部直径: i ide diameteri idediameterinside diameter 直径生长率: diameter increment percent
- Example Sentences:
| 1. | Kuroda uses : oversized bal preload for light to medium loading applications , and double nut ( pin method ) for medium and higher loading applications 对于轻度以及中度载荷应用场合,黑田采用增大钢球直径的办法实现预压加载;对于高负载场合,则采用双螺母方式。 | | 2. | The strength of extension of low carbon ductile cast iron can reach 750mpa in casting state , the impact ductility can reach 20j / cm2 . the diameter of graphite nodule is 5 - 20 ( am , the base body is consisted of pearlite - 低碳球铁在铸态下的抗拉强度可达750mpa ,冲击韧性可达20j cm ~ 2 ,其中石墨球直径在5 20 m ,基体以珠光体为主,有少量的铁素体与渗碳体。 | | 3. | The result of study indicated preliminarily that as for the bal cage patterned constant speed universal joint , while the number of steel ball increased from 6 to 8 , on account of the reduction of steel ball diameter , not only its outside dimension may cut down 12 % , its weight could get a reduction of nearly 20 % , but also the load bearing capacity of universal joint on the contrary could gain somewhat enhancement 研究结果初步表明,对于球笼式等速万向节,当钢球数量由6增加为8时,由于钢球直径的减小,不但其外形尺寸可以减小12 % 、质量可以减少近20 % ,而且万向节的承载能力反而可以得到少许提高。 | | 4. | As both the meshing point and ball ' s center are on the given cylinder , a general method for developing the cam ' s profile is studied . it is proved that the profile of positive and negative transmission is unique if the face gear , the difference between face tooth number and ball number and the diameter of ball are the same . the concrete expression of meshing cam on given spatial cycloid profile , and the characteristics of the profiles are discussed 论文的主要工作包括: 1 、根据啮合点和钢球中心轨迹均在同一圆柱面上的特点,研究了给定端齿齿廓条件下求解凸轮齿廓的一般方法;论证了在给定端齿、齿差数和钢球直径相同的条件下,正负齿差啮合齿廓的唯一性;讨论了端齿为球面摆线时,凸轮齿廓的具体表达式,并研究了该齿廓的性质。 | | 5. | Thirdly , through assaying the error generated during measuring data , the result manifests : 1 ) the location installed of the transducer and the point thumped affects the experiment result to some extent . if surface - opening cracks is deeper , the location of the transducers installed and the point thumped should be further away from the location of surface - opening cracks . 2 ) when the depth of surface - opening cracks is near to 50mm , it is very difficult to measure the depth of surface - opening cracks because the depth of r _ wave conveying in concrete plates from the different small ball bringing forth exceeds 50mm . 3 ) it is clear from the experiment result , the influence is n ' t big for the diameters of small balls to measure the data while the time interval between two transducers touched firstly has very big influence on the result 其次,对测量数据进行了误差分析,结果表明: ( 1 )传感器及敲击点的位置对实验结果有一定的影响,当开口裂纹的深度较深时,传感器和敲击点的位置应该离裂纹较远; ( 2 )当开口裂纹深度接近50毫米时,由于实验中所使用的小球产生的r波传播深度均超过50毫米,故很难测量出其开口裂纹的深度; ( 3 )实验发现,小钢球直径的大小对裂纹深度的测量结果影响并不是很大,但是,波的开始上升和下降点的测量精度(即两信号的时间延迟) ,对测量的结果有很大的影响。 |
- Similar Words:
- "球支承变速杆" English translation, "球支承座" English translation, "球之" English translation, "球之力量" English translation, "球之眼" English translation, "球直径变动量" English translation, "球止回阀" English translation, "球趾虎属" English translation, "球中期" English translation, "球中值" English translation
|
|
|