English translation for "焊接电压"

welding voltage
weldingvoltage

Related Translations:

焊接:  weld; welding; soldering; seal; sealing; sealing-in; shutting together 短语和例子电弧焊接 (electric) arc welding; 焊接材料 welding material; 焊接操作 welding operation; 焊接车间 welding shop; 焊接点 point of weld

电压:  voltage; electric tension; electric voltage

Example Sentences:

	1.	At the same time , the correcting valuation of laser hammering increases with the increment of pulse and voltage . the y direction is the major shift 焊接电压和脉宽越大,最高温度越高,热应力影响区越大,同时焊后校正偏移量越大。
	2.	Continuous adjusting and matching of welding voltage - current with led digital display , presetting and indicating of welding current , voltage and tractor speed available 焊接电压、电流连续可调与匹配，设有数显电流/电压表，可预设及显示焊接电流、电压及小车行走速度
	3.	Constant output characteristic is performed by voltage feedback , and the dynamic characteristic control of power supply is realized by modifying the reference voltage in di / dt feedback loop 利用电压负反馈实现所要求的平外特性。对电源动特性的控制通过改变反馈电路中的给定焊接电压实现。
	4.	In the closed loop , the information is transmitted to dsp from mcu and compared to the feedback data . then , the result would be transmitted back to the mcu for adjusting the wfs , voltage and so on to the setting values 采用闭环控制系统,将这些参数与反馈的数据比较、计算后,再通过da输出来调整和控制送丝速度,焊接电压等,使其保持在设定值。
	5.	Through the man - machine interaction system which consisted of lcd ( liquid crystal display ) and keyboards , we can select welding parameters , such as the way of welding , diameter of the wire , wire feed speed , current , voltage and so on 主要过程是:通过lcd ( liquidcrystaldisplay )与键盘组成的人机交互系统选择已存储在单片机flash中的焊接参数,包括焊接方法、焊丝直径、送丝速度、焊接电流、焊接电压等。
	6.	Due to two work states - - - arc burning and short current - - - existed in welding process of consumable electrode welding , and different control objectives in these two states , two close - loop feedbacks are designed in the control system : welding voltage feedback and welding current change rate feedback 根据熔化极co2焊机具有燃弧和短路两种工作状态，且两种状态下控制目标不同的特点，在控制系统中设计了双闭环反馈：焊接电压反馈及焊接电流变化率di / dt反馈。
	7.	Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting " . under the condition of constant diameter of welding wire and its feeding speed , the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply . if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition , the welding process will be stable with less spatter and smooth weld bead 通过分析不同焊接规范下的焊接电压和电流的波形.研究了水蒸气保护下电弧及熔滴过渡的特点，发现其电弧过程行为有“燃弧?熄弧?短路”和“燃弧?短路”两种形式.在焊丝直径和送丝速度一定的情况下，通过调节焊接回路中的电感量和电源电压，可以改变电弧的过程行为形式.若电弧过程呈“燃弧?熄弧?短路”交替进行，并且熄弧时间最短时，短路过渡频率最高，在这种情况下，飞溅小，焊道成型好，焊接过程稳定

Similar Words：

"焊接电流调整范围" English translation, "焊接电流范围" English translation, "焊接电流衰减时间" English translation, "焊接电流增加时间" English translation, "焊接电路" English translation, "焊接电源" English translation, "焊接电源电压" English translation, "焊接电阻器" English translation, "焊接调定值" English translation, "焊接调节器" English translation