English translation for "料面"

charge level
charge lever

Example Sentences:

	1.	It is pointed out that length of flown - in material ( lfm ) , which flows into female die from underside of blank - holder during forming , is an external index of local forming resistance 提出将流入量(从压料面下进入凹模型腔的局部材料线素长度)作为衡量局部成形阻力的指标。
	2.	Abstract : in this paper , the distinct element method is adopted to study the force and the motion of granular burden from a kinematic view point . the numerical model of bell - less top charging is established . the charging process and burden surface profile have been imitated 文摘:从动力学角度，采用离散单元法研究炉料颗粒的受力和运动，建立高炉无钟炉顶布料数值计算模型，模拟无钟炉顶布料过程和料面形状。
	3.	Abstract : the reasonable distribution of mix bulk density and partical size on the transverse and lenghwise direction of sintering pallet , the relationship between segregation index and mix bulk density were discussed . the ways for improving mix bulk density , enhancing mix partical segregation , decreasing side wall effect and increasing bed surface flatness were proposed 文摘:论述了台车上横向、纵向混合料容积密度及粒度的合理分布,偏析指数和混合料容积密度的关系,提出了改善台车上混合料容积密度，加大混合料粒度偏析,降低边缘效应及提高料面平整度的布料途径。
	4.	This paper referred to the massive domestic and foreign technical material , elaborated in the sheet forming value simulation theory essential technology in detail , points out when analysis sheet forming question should use the big distortion ball plasticity fem and introduce the application characteristic and the function summarizes of the sheet forming simulation software dynaform . secondly , analyzed the cover forming characteristic , simultaneously introduced the influence cover forming factor in detail : such as ramming direction , the craft addendum surface and the material pressing surface , the radius of convex - concave mold , draw bead , pressure strength , blank size and craft margin and so on . and simulates many typical automobiles cover panel with software : such lateral board , back taillight pedestal and storage cover 其次,分析了覆盖件成形的特点和要求,同时详细介绍了影响覆盖件成形的因素如冲压方向、工艺补充面和压料面、凸凹模圆角、拉延筋、压边力、坯料尺寸和工艺切口等,并用数值模拟软件对多个典型的汽车覆盖件汽车后侧围板、后灯座以及轿车后备箱盖的冲压成形情况进行模拟,用模拟结果优化拉延工艺方案,比较了内覆盖件和外覆盖件在成形特点和要求的一些异同点,以及常见的起皱、拉裂和回弹、成形不足等缺陷的产生机理和相应对策,重点介绍工艺补充面和压料面的设计及优化方法,因为拉延是冲压工艺的关键工序,而工艺补充面和压料面的设计是拉延工序的关键,对消除缺陷至关重要。
	5.	Through the experimental research , we think : the technological capacity of fiberglass asphalt macadam if weaker than asphalt macadam , however , if use elasticized capacity to solve blending technological problem . adjust the breed of fiber silk , extend its diameter , its paving capacity is still worth exploring , asphalt - rubber macadam structure lager have good deformed - become capacity and crazed - resistance capacity , small gap rate . good water - resistance capacity , good hot - stability and simple construction technology . therefore . pitch rubber spall is a good cover material which is suitable for the second class or lower whose asphalt pavement has split open because of fatigue . and is the good structural measure of preventing half - rigidity grass - roots unit shrink - rift reflecting . pave a thin layer of pitch rubber spall between asphalt - type pavement layer and half - rigidity basic level , although the cost of building is higher than paving togongbu in the middle , the construction technology , crazing - resistance and water - resistance are better than togongbu , not only could reduce greatly the reflex of half - rigidity grass - roots unit material , long then the use lifespan of pavement , but also it is possible to reduce suitably the thickness of asphalt mixture layer , though the cast of building in the early days becomes more , in the long - term opinion , it have fully important technological and economical significance 通过试验研究认为：玻璃纤维沥青碎石的技术性能不如沥青碎石好，但路用弹性性能较好，如能解决拌和工艺问题，调整纤维丝的品种，增大其直径，其路用性能仍值得探讨，沥青橡胶碎石结构层具有变形性能和抗裂性能良好，空隙率小，防水性能好，热稳定性较好，施工工艺简单的特点，因此，沥青橡胶碎石是二级及二级以下公路因疲劳而开裂的沥青路面的良好罩面材料，也是防止半刚性基层收缩裂缝反射的良好结构措施，在沥青类路面面层和半刚性基层之间夹铺沥青橡胶碎石薄层，虽然造价比夹铺土工布高，但其施工工艺，抗裂性能和防水性能均优于土工布，不仅可以大大减少半刚性基层材料的反射裂缝，延长路面使用寿命，而且可能适当减薄沥青混合料面层的厚度，虽然初期造价有所增加，从长远来看，具有十分重要的技术和经济意义。

Similar Words：

"料垄迹印" English translation, "料垄迹印（料纹）" English translation, "料垄形成" English translation, "料罗" English translation, "料门" English translation, "料面测量仪表" English translation, "料面测探器" English translation, "料面计" English translation, "料面探测器" English translation, "料面指示控制器" English translation