English translation for "散热条件"
|
- heat dissipation conditions
Related Translations:
呼吸散热: respiratory heat loss 散热表面: heat delivery surfaceheat-delivery surface 散热率: heat dissipation ratethermal output 散热源: source of heat release 散热途径: route of heat dissipation
- Example Sentences:
| 1. | Therefore , the work presents a foundation for modifying heat release conduction and designing cooling installation
结果表明，用所提出的方法计算减速器散热系数符合实际，为改善散热条件和设计冷却装置提供了依据。 | | 2. | The product is plateau type . its insulation strength , transportation requirement , radiation condition and overall appearance can sufficiently meet the operation requirement in plateau area
产品全部为高原型，其绝缘强度、运输要求、散热条件、外观等均经过大量研究，能充分满足高原地区的运行要求。 | | 3. | Depending the pneumatic delivers to torque , the construction is simple , make and installing the technique request to be low , thermolysis would be better to not as good as ventilated type , the pneumatic capacity is bigger , the aeration and deflate time longer , easy is slippery
靠气胎传递扭矩，结构简单，制造、安装技术要求低，散热条件不如通风型，气胎容积较大，充气、放气时间较长，容易打滑。 | | 4. | For example , when using pid control method of controlling the electrical current of the discharge , with the discharge tube exposed to the outside with very good thermal dispersion conditions , unrestrained thermal expansion back - pack style he - ne laser tube gave good results
采用控制激光器的放电电流的pid控制模式，在放电管外露，散热条件好；热变形不受约束的背包式he - ne激光管上取得了很好的效果。 | | 5. | However , unsatisfactory results were obtained under the following conditions : discharge tube covered with glass cover , thermal dispersion conditions not as effective , thermal expansion of the discharge tube restricted by the co - axis glass cover ( longer preheat time , lower anti - interference )
在放电管外有玻璃罩，散热条件差；放电管温度变形受外玻璃罩约束的同轴式管子上则效果不理想(预热时间较长，抗干扰能力不如前者) 。 | | 6. | According to the ventilation and heat dispersion of the motor , this paper takes two parameters that are closely related with the heating of the motor to work out a practical simplified calculative formula , and further gets it verified with two examples under continuous and intermittent duty respectively
摘要根据电机的通风散热条件，用与电机发热密切有关的两个参数给出实用的简化计算公式，并用此公式计算了电机连续和断续负载温升的两个实例。 | | 7. | As to the video signal , alarm signal , control signal , are all weak electricity signal , exceedingly easily be subjected to the jam , in case the power supply system does not steady , wave propag ation is greatly , the harmonic content of power source overtops , the veins wave factors are great unduly , and even power source equipment breakdown , outputting abnormal , will be about to affect the video signal image effect , and dependability cuts downs to the security and alarming system . we adopt fast fu lye ' s mutation rule - fft alternatives , by the way of carrying fft alternatives to the local junction circuit , regulated power supply , ups ' s power source , and switch power source , thereby diagnose every degree harmonious wave content of power souse , and abnormal coefficient , compared to the normal working situation . thereby diagnose out the working condition of the regulated power supply , ups ' s power source , and switch power source
如果有供电系统不稳定、波动大，电源的谐波含量过高，纹波系数过大，乃至电源设备损坏、输出异常等情况出现，将会严重影响视频信号的图像效果，大大降低防盗系统的稳定性和可靠性，我们采用快速傅利叶变换原理，即fft变换，通过对市电、稳压电源、 ups电源、开关电源等的电压信号进行fft变换，从而得出信号中各次谐波的含量及信号畸变系数，并将其与正常工况下的参数进行对比，从而进一步诊断出稳压电源、 ups电源、开关电源等设备的运行状况；组成监控系统的设备长期处于工作状态，往往由于设备散热条件不好、设备老化故障等原因导致设备表面温度过高，从而影响设备的正常运行，降低设备的使用寿命。 | | 8. | Now if we suppose that the rated temperature limit of any chip were identical , confining the highest temperature in the rated limit is the most important , for this purpose i apply the principle of annealing algorithm to the optimization of place distribution design . under the unvaried condition of thermal dispersion , we can get the least temperature of the maximum value in some kind of chip array
为了使得电子元件最大温度负荷在特定散热状态下达到最低(低于额定的最高温度值) ，我们将模拟退火算法的优化设计思想应用到电子元件阵列的布局优化中，使得在不改变外部散热条件的情况下，仅仅通过电子元件位置分布的改变就取得降低其最高工作温度的效果。 | | 9. | Firstly , considering the molecular pump is small and the elimination of heat condition is bad , this paper presents the structure of the mb , including the material of the rotor and stator , the number of magnetic poles , the stator slot shape of mb , the layout of the magnetic poles , the coins winding and so on
首先综合考虑了分子泵体积小、磁轴承散热条件不好的特点,设计了分子泵磁悬浮轴承的结构,选择了轴承铁芯的材料,设计了磁极的布置、槽的形状、磁极数目和线圈缠绕方式。 | | 10. | Double - clad pumped yb - doped fiber laser has the advantages of compact structure , simple cooling , broad pumping wavelength , high efficiency , high power , long - life . there are many applications of fiber laser in optical communication , industry process , medical treatment , laser printing and label - making
双包层泵浦掺镱光纤激光器具有结构紧凑、散热条件简单、泵浦范围宽、高效率、高功率、寿命长等优点，在光通讯、工业加工、医疗、激光印刷打标等领域有着广泛的应用。 |
- Similar Words：
- "散热式镂空" English translation, "散热速率" English translation, "散热损失" English translation, "散热体" English translation, "散热条" English translation, "散热凸缘" English translation, "散热凸缘, 散热片" English translation, "散热途径" English translation, "散热系数" English translation, "散热系统" English translation
|
|
|
