English translation for "塑性变形区"
|
- plastically deforming area
zone of plastic deformation
Related Translations:
塑性变形: after flowcreepageductile deformationheaveirrecoverable deformationirreversible deformationplactic deformationplastic deformationplastic distortionplastic flowplastic strainplastic yieldin 弹塑性变形: elastic plastic deformationelastic-plastic deformationelastico-plastic defomationelasto plastic deformationelastoplastic deformationplastoelastic deformation 临界塑性变形: critical plastic deformation 超塑性变形: superplastic deformation 塑性变形蔓延: plasticity propagation 塑性变形集中: concentration of plastic deformationconceptual earthquake―resistant design 晶格塑性变形: plastic deformation of the lattice 塑性变形率: index of plastic deformation
- Example Sentences:
| 1. | The fifth chapter makes a technological analysis to the engine bolt on the whole and put forward the application of plasticity out of shape district control law and elasticity out of shape district corner control law to the keys parts of the engines , including connecting rod and main bearing
第五章对发动机螺栓紧固技术作了技术分析，提出了塑性变形区控制法和弹性变形区转角控制法在发动机关键部位螺栓，如连杆、曲轴主轴承盖上的应用。 | | 2. | It shows that at the stress concentration zone , changes of mfl were relatively weak with slight deformation of the specimens . with the deforming to plastic and further the changing of mfl exhibits more distinct , and when necking emerging a very intensive change takes place . it is indicated that magnetic memory effect is related to the microstructure of the material
经分析认为,磁记忆信号的这种变化与材料内部微观组织的状态有关,试件变形很小时,磁弹性效应对试件表面泄漏磁场的变化起主要作用;试件变形较大时,其表面泄漏磁场的变化主要受塑性变形区内位错聚集产生的微缺陷的影响。 | | 3. | The five reason of the formation and development of the plug is considered , and the rheology of soil body in the plastic deformation area is especially pointed out ; the statistic model is built in order to calculate the plug ' s length , and the practical significance of the model parameters is given out . it plays an important role on predicting the length of the plug in the process of penetration
通过多种试验对土塞形成的原因进行了分析，提出土塞产生的流变原因，该流变的一个显著特点是作为塑性变形区整块土体受负压作用，而塑性变形区内部土体受向上的渗流作用，这两种作用都是土塞形成和发展的积极因素。 | | 4. | The calculation results indicate that the outboard of drum walls fall in plastic yielding at the same time the rising cooling water reaches the height of that point and the yield region becomes narrower and narrower when it comes closer to the circumferential strake weldments , which explains the reason coke drums experience bulging and cracks occur in the weld seams portions of shell to shell after long in service
计算结果表明：塔壁外侧在冷却水面到达的瞬间进入塑性屈服，筒节中部塑性屈服区较大，当靠近焊缝时塔壁的塑性变形区逐渐缩小直至消失，塔壁塑性屈服区的分布特点解释了塔体长期使用后发生鼓凸变形及简体与焊缝连接处产生裂纹的原因。 | | 5. | The content of this thesis , through the deformation destruction process of th e typical nanlidu landslide along the national highway 318 , uses the finite unit a nalysis of computation , revealing the elastic , plastic stress and displacement of each joint inside the slide area pointing out the distribution range of the tension stress and the plastic deformation range , computering the stability safety factor of the slide area , gaining the fixed quantity , quota that evaluates the stability of the slide area , revealing the position of the slide area which is most likely to los e its stability , thus , it can provide theoretic proof for the programs which renova te landslides
本文的研究内容是通过318国道南里渡典型滑坡的变形破坏过程，采用有限元计算分析，揭示滑体内部每个节点上的弹、塑性应力及位移，找出拉应力分布区和塑性变形区，计算滑体稳定安全系数，得出衡量滑体稳定的定量指标，揭示滑体最可能失稳的部位，从而为滑坡整治方案提供理论依据。 |
- Similar Words：
- "塑性变形理论" English translation, "塑性变形率" English translation, "塑性变形蔓延" English translation, "塑性变形能" English translation, "塑性变形判别衡准" English translation, "塑性变形曲线描记仪" English translation, "塑性变形曲线描记仪 塑性形变记录仪" English translation, "塑性变形时间关系图" English translation, "塑性变形图描记录器" English translation, "塑性变形图描记器" English translation
|
|
|
