English translation for "叶片出水边"

outlet edge of vane

Related Translations:

赛出水平赛出风格:  give the best account of oneself and display fine sportsmanship

定型叶片:  profile blade

标记叶片:  index blade

叶片螺距:  blade pitch

三维叶片:  three dimensional blade

支撑叶片:  support blade

叶片工作面:  front side of vaneleading face of vaneleading side of bladeleading-out side of blade

螺旋叶片:  auger flighthelical bladehelicallobe

旋流叶片:  intervaneswirl vaneswirler vane

叶片深度:  depth of blade

Example Sentences:

	1.	On basis of numerical simulation , the optimized weling technological has been vadidated and adjusted by plane test , results show that residual stress of both ends welded in advance can be decreased by the interspace welded later , and decreasing effect is the most obvious in the 50mm range of the interspace ; for local heating , it is 60mm from the edge of heated area to decrease residual stress 通过平板试验得到了分段焊与局部加热合理工艺参数,并在此基础上,对转轮的焊接残余应力场进行了调整与控制,使叶片出水边危险区域附近产生了较大的残余压应力,且转轮整体的残余应力水平低于转轮材料屈服极限的三分之一。
	2.	The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation . the result shows that welding residual tensile stress appears in the weld and its area nearby , and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding , and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time , heating temperature , heating area , and inversely proportional to cooling area , and welding residual tensile peak stress in the dangerous area is decreasing trend earlier , and then increasing trend later with heated location increased 本文利用数值模拟手段对转轮的焊接工艺从分段焊和局部加热两个方面进行了优化,结果表明:采用普通工艺焊接时,叶片焊后残余拉应力出现在焊缝及其附近区域,并且在叶片出水边的熔合线附近(危险区域)出现了峰值;在采用优化的分段焊时,先焊两端后焊中间的方法可以降低叶片危险区域的焊接残余拉应力峰值,降低效果与叶片出水边焊段长度、焊缝各段的焊接方向有关;局部加热法降低转轮危险区域残余应力的效果主要与加热时间、加热温度以及加热面积成正比,与冷却面积成反比,并且危险区域的残余应力随加热区域的增大呈先降低后升高的趋势。

Similar Words：

"叶片出口边" English translation, "叶片出口角" English translation, "叶片出口角叶片出口角" English translation, "叶片出汽边" English translation, "叶片出汽边 后沿 下降边" English translation, "叶片大安装角" English translation, "叶片大而爆盾形" English translation, "叶片弹簧" English translation, "叶片弹簧成形机" English translation, "叶片弹簧淬火机" English translation