English translation for "入口端"
|
- arrival end
entry end
inlet end
Related Translations:
入口: 1.(进入嘴中) enter the mouth 短语和例子难于入口 have a nasty taste; 不可入口 ! not to be taken orally!2.(进入的门或口儿; 输入) entrance; entry; inlet; introitus; aditus; throat; threshold 短语和例子车站入口处 entrance to the 城堡入口: castlevania enterance
- Example Sentences:
| 1. | The ac power lines and the telecommunication lines should be referenced together at the building entry point
在建筑物入口端，电源线和通信线应该连接一起接地。 | | 2. | The foam carpet is 900m after the threshold , it is 15m wide and 800m long , report established on the localizer
泡沫垫在跑道入口端以后900米， 15米宽， 800米长，对准航向时报告。 | | 3. | Alignment . the axes of the threaded inlet and outlet ends shall be [ b ] [ red ] within 1 . 0 of the angle specified [ / red ] [ / b ]
对齐。带螺纹的流体入口端面与出口端面的轴线允许所规定的角度的1 . 0上下范围内波动。 | | 4. | The ac power lines should be protected at the origin ( building entry point ) and at each of the succeeding protection zones within the building
电力线的入线端（即建筑物入口端）以及建筑物内随后的各防护区处都应加以防护。 | | 5. | In this paper , high heat penetration into a moving particulate bed is described mathematically with a comprehensive heat and mass transfer model . the distribution of gas velocity and pressure , the temperature field of gas and solid in the moving particulate bed are examined for different conditions . the results show that thermal penetration into the moving packed - bed particles by fluid flow in porous media is high only in the position near the gas entrance . the thermal penetration thickness tends to increase with the fluid flow velocity and decrease with the particle moving velocity . in the region of thermal penetration , the porosity of solid bed has significant effect on gas field and pressure loss . it is feasible to reduce the gas pressure loss by a larger width / height packed bed in design and operation . the correspondence between thermal infection depth and particle bed height would be helpful to keep high oapacity of reactor and reduce the cost of operation
针对移动颗粒床中物料层内的高温气体渗流传热现象，考虑渗流与传热的相互作用，采用局部非热平衡假设建立了多孔介质渗流传热物理数学模型并进行了数值计算.研究了不同情况下床内填充多孔介质中的流速、气固温度和床层压力损失.计算结果表明，高温热气对移动床颗粒料层的热渗透主要发生在渗流入口端区域，增大入口渗流速度以及减小床层物料下移速度将导致物料温度沿床高慢速下降，热渗透深度扩大，热渗透作用区域内的物料温度水平提高.在热渗透作用区域，孔隙率对流场和压力损失有很大的影响.研究结果对于移动颗粒床反应器的设计与运行具有一定的参考作用 | | 6. | These methods are following : ( 1 ) in order to build fem model conveniently and enhance calculating speed , interceped a finite length and built a 2d - symmetry model . ( 2 ) in order to apply loads conveniently , kept the entrance of cold fluid . ( 3 ) in order to obtain numerical results in steady situation , lengthened export and import ends
这些方法主要有： ( 1 )为了便于建立模型并提高计算速度，对于实际工程中采用的长径比特别大的换热管采取截取有限长度的方法并建立二维对称简化模型； ( 2 )提出采取保留冷流体入口端，截取有限长度的方法施加载荷； ( 3 )适当延长翅片管的出口端和入口端，以便获得稳定工况的数值解。 |
- Similar Words：
- "入口点地址" English translation, "入口调用语句" English translation, "入口定位点" English translation, "入口动压降" English translation, "入口动作" English translation, "入口端管" English translation, "入口段" English translation, "入口断面" English translation, "入口队列" English translation, "入口阀" English translation
|
|
|
