Chinese translation for "成形件"

drip moulding
formed part
shaped objects

Related Translations:

成形放大器:  processing amplifier

内成形:  internal shaping

成形刀架:  forming rest

冷轧成形:  cold roll forming

成形绕组:  preformed winding

成形直径:  form diameter

铸造成形:  cast form

粉末成形:  powder forming

成形模具:  forming die(t001)

注入成形:  encapsulation molding

Example Sentences:

	1.	Necessary pressure tubes and steel beams may be either incorporated in the block or added later, depending on the design . 按设计要求，必要的压力导管和钢梁可以与成形件做在一起，也可以以后再加。
	2.	Comparative study on the surface properties of sl and fdm parts 成形件表面性能的对比研究
	3.	The microstructure of lsf components was made up of fine columnar dendrites , which grow epitaxially from the substrate , and the mean primary dendrite spacing was 26 . 58 m 对成形件微观组织的研究发现其组织主要由外延生长的细长枝晶组成，枝晶一次间距平均为26 . 58 m 。
	4.	The primary research can be listed as follows . in this thesis , a control volume method was employed to model the microstructure of 3 - d braided performs produced by the four - step 1 1 square braiding process and their reinforced composite materials 主要的研究内容包括以下几个方面：系统地研究了采用四步法1 1方型编织工艺编织的预成形件及其增强的复合材料的细观结构。
	5.	Examination of the density , strength , hardness and microstructure showed that the mechanical properties and structure of the part made by direct metal forming process are better than that obtained from selective laser sintering process , as good as or even better than castings 对成形件进行的密度、强度和硬度指标测试和金相组织观察表明：基于弧焊的直接金属成形件的组织结构和力学性能指标明显优于选择性激光烧结工艺成形件，达到或高于铸造零件。
	6.	The simulation of hemisphere bulging shows that the thin rate decreases about 10 % with direct - reverse process . cavity rate is decreased evidently in the bulging if back pressure is provided . experiment shows that proper back pressure can eliminate big cavity on the condition that strain is not very high 通过增加胀形背压,降低成形件的空洞率,结果显示背压对于空洞率的降低有比较明显的作用,适当的背压甚至可以基本消除应变不是特别大时的空洞。
	7.	The results showed that the processing parameters ( such as laser power , the diameter of laser , scanning speed of laser beam , ratio of overlapping ) are important to acquire a perfect component . furthermore , in order to assure geometric properties ( accuracy , surface finish ) , the structure of the off - axial powder nozzle was improved to avoid the oxidation of the molten pool . the density metal test sample of rene95 high - temperature alloy was made by lsf through optimizing the processing parameters 本文对激光立体成形的工艺特性进行了深入系统的研究，发现如果要获得理想的成形效果，就必须对成形过程中的工艺参数进行精密控制，例如激光功率、激光光斑大小、光束扫描速度、搭接率等；同时为了保证成形件有较高的尺寸精度和表面质量，必须对成形零件的氧化问题进行控制，通过改进侧向送粉喷嘴的结构设计，成形件的表面氧化问题得到适度控制。
	8.	According to the movement traces of yarn carriers on the braiding machine bed , a perform was divided into three regions , i . e . interior , surface and corner , and distinct control volumes were defined for each region . analyzing the control volume of each region , the yarn architecture of perform was described and three kinds of local unit cell were identified . then the relations between the braiding parameters of the perform were derived 根据编织过程中携纱器的运动轨迹特点，将预成形件划分为三个不同的区域，分别定义了不同的控制体积单元，识别了预成形件的两种局部单胞模型，分析了预成形件的纱线构造，并导出了编织结构参数之间的关系，同时给出三维编织复合材料的设计方法。
	9.	The mechanical property of the test sample was improved through heat treatment further . after heat treatment process , the primary strengthening phase y " increased both in the quantity and size . the quantity of phase y " increased to 45 % and the size of them became more uniform ( about 100nm ) as the test sample experienced heat treatment 为了提高成形件的力学性能，对试样进行了热处理，经过热处理后，试样的主要强化相相无论是数量还是尺寸都有显著变化，数量经过热处理后增加到45左右，原始尺寸从大小不等到经过热处理后更加均匀，平均尺寸为100nm 。
	10.	In - depth knowledge of supplier base in the following manufacturing processes / products : investment / lost - wax / precision casting , zinc die - castings , aluminum casting ( gravity & pressure ) , iron casting , permanent mold casting , sand casting , powdered metallurgy , mim , steel forging , brass forging , cold forming , stamping , deep drawing , fine blanking , machining ( milling , turning , etc . ) , sheet metal fabrication , screw machining , cnc machining , mould making , tool & die , assembly , fasteners , springs , etc 对以下金属制造工艺/零部件的供应商有资深专业经验：脱蜡/精铸件，锌合金压铸件，铝铸件（浇铸或压铸） ，铁铸件，永久模铸件，沙铸，粉状冶金零件，金属粉末注射成形件，钢铁锻造，黄铜锻造，冷锻/冷镦，冲压件，拉深引深件，精密下料，机加件（自动车，数控机床，铣，车，磨等） ，板金件，制模及模具装配、标准件，弹簧类。

Similar Words：

"成形技术" Chinese translation, "成形剂" Chinese translation, "成形加工" Chinese translation, "成形架" Chinese translation, "成形键槽" Chinese translation, "成形件装拆钳" Chinese translation, "成形介质" Chinese translation, "成形金属丝" Chinese translation, "成形剧" Chinese translation, "成形绝热材" Chinese translation