English translation for "welding voltage"

电弧电压
焊接电压

Related Translations:

voltage:  n.【电学】电压，电压量，伏特数。 the working voltage (电气的)耐压限度。

Example Sentences:

	1.	Continuous adjusting and matching of welding voltage - current with led digital display , presetting and indicating of welding current , voltage and tractor speed available 焊接电压、电流连续可调与匹配，设有数显电流/电压表，可预设及显示焊接电流、电压及小车行走速度
	2.	For the welding voltage doesn ' t change , so the arc length also will not change , and the arc will penetrate into the molten puddle , which will make the swing range small , so the fusion width will decrease 由于电压没有改变，所以弧厂也不变，导致电弧潜入熔池，使电弧摆动范围缩小，就是促使容熔宽减小。
	3.	Due to two work states - - - arc burning and short current - - - existed in welding process of consumable electrode welding , and different control objectives in these two states , two close - loop feedbacks are designed in the control system : welding voltage feedback and welding current change rate feedback 根据熔化极co2焊机具有燃弧和短路两种工作状态，且两种状态下控制目标不同的特点，在控制系统中设计了双闭环反馈：焊接电压反馈及焊接电流变化率di / dt反馈。
	4.	Aiming at the problems of the k190jik rail welding machine , that the parameter modification is difficult , the welding process is not enough stability and the welding machine has no on - line diagnosis function , in this paper , the control system of the welding machine was promoted completely adopting the fx2n - 64mr programmable logic controller and the pcl - 1800 data acquisition card , the das ( data acquisition system ) was set up by using labview and visual basic software , the functions of welding voltage stabilizing and adjusting , current controlling and intellectual modification was improved , welding quality diagnosis system was built up , and the assembling and debugging of the control system was completed , including the process experiments 本文针对k190jik钢轨焊机控制系统存在参数修改困难、焊接过程不够稳定、无焊接质量在线诊断功能等问题，采用日本三菱公司fx2n - 64mr可编程序控制器、研华工控pcl ? 1800数据采集卡等为核心控制部件，对焊机的整机控制系统进行了全面升级。运用软件labview和vb开发了数据采集系统，完善了焊接稳压、调压、电流恒值控制与智能调节功能，利用vb建立了焊接质量在线诊断系统，并完成了系统组装调试与工艺试验研究工作。
	5.	Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting " . under the condition of constant diameter of welding wire and its feeding speed , the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply . if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition , the welding process will be stable with less spatter and smooth weld bead 通过分析不同焊接规范下的焊接电压和电流的波形.研究了水蒸气保护下电弧及熔滴过渡的特点，发现其电弧过程行为有“燃弧?熄弧?短路”和“燃弧?短路”两种形式.在焊丝直径和送丝速度一定的情况下，通过调节焊接回路中的电感量和电源电压，可以改变电弧的过程行为形式.若电弧过程呈“燃弧?熄弧?短路”交替进行，并且熄弧时间最短时，短路过渡频率最高，在这种情况下，飞溅小，焊道成型好，焊接过程稳定

Similar Words：

"welding up" English translation, "welding up of blowholes" English translation, "welding v" English translation, "welding variable" English translation, "welding variables" English translation, "welding wheel" English translation, "welding wire coil" English translation, "welding wire coiler" English translation, "welding wire for shipbuilding" English translation, "welding wire machine" English translation